This is a purely informative rendering of an RFC that includes verified errata. This rendering may not be used as a reference.

The following 'Verified' errata have been incorporated in this document: EID 4845
Internet Engineering Task Force (IETF)                        A. Ramaiah
Request for Comments: 5961                                         Cisco
Category: Standards Track                                     R. Stewart
ISSN: 2070-1721                                                   Huawei
                                                                M. Dalal
                                                             August 2010

         Improving TCP's Robustness to Blind In-Window Attacks


   TCP has historically been considered to be protected against spoofed
   off-path packet injection attacks by relying on the fact that it is
   difficult to guess the 4-tuple (the source and destination IP
   addresses and the source and destination ports) in combination with
   the 32-bit sequence number(s).  A combination of increasing window
   sizes and applications using longer-term connections (e.g., H-323 or
   Border Gateway Protocol (BGP) [RFC4271]) have left modern TCP
   implementations more vulnerable to these types of spoofed packet
   injection attacks.

   Many of these long-term TCP applications tend to have predictable IP
   addresses and ports that makes it far easier for the 4-tuple (4-tuple
   is the same as the socket pair mentioned in RFC 793) to be guessed.
   Having guessed the 4-tuple correctly, an attacker can inject a TCP
   segment with the RST bit set, the SYN bit set or data into a TCP
   connection by systematically guessing the sequence number of the
   spoofed segment to be in the current receive window.  This can cause
   the connection to abort or cause data corruption.  This document
   specifies small modifications to the way TCP handles inbound segments
   that can reduce the chances of a successful attack.

Status of This Memo

   This is an Internet Standards Track document.

   This document is a product of the Internet Engineering Task Force
   (IETF).  It represents the consensus of the IETF community.  It has
   received public review and has been approved for publication by the
   Internet Engineering Steering Group (IESG).  Further information on
   Internet Standards is available in Section 2 of RFC 5741.

   Information about the current status of this document, any errata,
   and how to provide feedback on it may be obtained at

Copyright Notice

   Copyright (c) 2010 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   ( in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1. Introduction ....................................................3
      1.1. Applicability Statement ....................................3
      1.2. Basic Attack Methodology ...................................4
      1.3. Attack probabilities .......................................5
   2. Terminology .....................................................7
   3. Blind Reset Attack Using the RST Bit ............................7
      3.1. Description of the Attack ..................................7
      3.2. Mitigation .................................................7
   4. Blind Reset Attack Using the SYN Bit ............................9
      4.1. Description of the Attack ..................................9
      4.2. Mitigation .................................................9
   5. Blind Data Injection Attack ....................................10
      5.1. Description of the Attack .................................10
      5.2. Mitigation ................................................11
   6. Suggested Mitigation Strengths .................................12
   7. ACK Throttling .................................................12
   8. Backward Compatibility and Other Considerations ................13
   9. Middlebox Considerations .......................................14
      9.1. Middlebox That Resend RSTs ................................14
      9.2. Middleboxes That Advance Sequence Numbers .................15
      9.3. Middleboxes That Drop the Challenge ACK ...................15
   10. Security Considerations .......................................16
   11. Contributors ..................................................17
   12. Acknowledgments ...............................................17
   13. References ....................................................17
      13.1. Normative References .....................................17
      13.2. Informative References ...................................17

1.  Introduction

   TCP [RFC0793] is widely deployed and the most common reliable end-to-
   end transport protocol used for data communication in today's
   Internet.  Yet, when it was standardized over 20 years ago, the
   Internet was a different place, lacking many of the threats that are
   now common.  The off-path TCP spoofing attacks, which are seen in the
   Internet today, fall into this category.

   In a TCP spoofing attack, an off-path attacker crafts TCP packets by
   forging the IP source and destination addresses as well as the source
   and destination ports (referred to as a 4-tuple value in this
   document).  The targeted TCP endpoint will then associate such a
   packet with an existing TCP connection.  It needs to be noted that,
   guessing this 4-tuple value is not always easy for an attacker.  But
   there are some applications (e.g., BGP [RFC4271]) that have a
   tendency to use the same set(s) of ports on either endpoint, making
   the odds of correctly guessing the 4-tuple value much easier.  When
   an attacker is successful in guessing the 4-tuple value, one of three
   types of injection attacks may be waged against a long-lived
   RST -  Where an attacker injects a RST segment hoping to cause the
      connection to be torn down.  "RST segment" here refers to a TCP
      segment with the RST bit set.
   SYN -  Where an attacker injects a SYN hoping to cause the receiver
      to believe the peer has restarted and therefore tear down the
      connection state.  "SYN segment" here refers to a TCP segment with
      SYN bit set.
   DATA -  Where an attacker tries to inject a DATA segment to corrupt
      the contents of the transmission.  "DATA segment" here refers to
      any TCP segment containing data.

1.1.  Applicability Statement

   This document talks about some known in-window attacks and suitable
   defenses against these.  The mitigations suggested in this document
   SHOULD be implemented in devices that regularly need to maintain TCP
   connections of the kind most vulnerable to the attacks described in
   this document.  Examples of such TCP connections are the ones that
   tend to be long-lived and where the connection endpoints can be
   determined, in cases where no auxiliary anti-spoofing protection
   mechanisms like TCP MD5 [RFC2385] can be deployed.  These mitigations
   MAY be implemented in other cases.

1.2.  Basic Attack Methodology

   Focusing upon the RST attack, we examine this attack in more detail
   to get an overview as to how it works and how this document addresses
   the issue.  For this attack, the goal is for the attacker to cause
   one of the two endpoints of the connection to incorrectly tear down
   the connection state, effectively aborting the connection.  One of
   the important things to note is that for the attack to succeed the
   RST needs to be in the valid receive window.  It also needs to be
   emphasized that the receive window is independent of the current
   congestion window of the TCP connection.  The attacker would try to
   forge many RST segments to try to cover the space of possible windows
   by putting out a packet in each potential window.  To do this, the
   attacker needs to have or guess several pieces of information namely:

   1) The 4-tuple value containing the IP address and TCP port number of
      both ends of the connection.  For one side (usually the server),
      guessing the port number is a trivial exercise.  The client side
      may or may not be easy for an attacker to guess depending on a
      number of factors, most notably the operating system and
      application involved.

   2) A sequence number that will be used in the RST.  This sequence
      number will be a starting point for a series of guesses to attempt
      to present a RST segment to a connection endpoint that would be
      acceptable to it.  Any random value may be used to guess the
      starting sequence number.

   3) The window size that the two endpoints are using.  This value does
      NOT have to be the exact window size since a smaller value used in
      lieu of the correct one will just cause the attacker to generate
      more segments before succeeding in his mischief.  Most modern
      operating systems have a default window size that usually is
      applied to most connections.  Some applications however may change
      the window size to better suit the needs of the application.  So
      often times the attacker, with a fair degree of certainty (knowing
      the application that is under attack), can come up with a very
      close approximation as to the actual window size in use on the

   After assembling the above set of information, the attacker begins
   sending spoofed TCP segments with the RST bit set and a guessed TCP
   sequence number.  Each time a new RST segment is sent, the sequence
   number guess is incremented by the window size.  The feasibility of
   this methodology (without mitigations) was first shown in [SITW].
   This is because [RFC0793] specifies that any RST within the current
   window is acceptable.  Also, [RFC4953] talks about the probability of
   a successful attack with varying window sizes and bandwidth.

   A slight enhancement to TCP's segment processing rules can be made,
   which makes such an attack much more difficult to accomplish.  If the
   receiver examines the incoming RST segment and validates that the
   sequence number exactly matches the sequence number that is next
   expected, then such an attack becomes much more difficult than
   outlined in [SITW] (i.e., the attacker would have to generate 1/2 the
   entire sequence space, on average).  This document will discuss the
   exact details of what needs to be changed within TCP's segment
   processing rules to mitigate all three types of attacks (RST, SYN,
   and DATA).

1.3.  Attack probabilities

   Every application has control of a number of factors that drastically
   affect the probability of a successful spoofing attack.  These
   factors include such things as:

   Window Size  - Normally settable by the application but often times
      defaulting to 32,768 or 65,535 depending upon the operating system
      (see Figure 6 of [Medina05]).

   Server Port number  - This value is normally a fixed value so that a
      client will know where to connect to the peer.  Thus, this value
      normally provides no additional protection.

   Client Port number  - This value may be a random ephemeral value, if
      so, this makes a spoofing attack more difficult.  There are some
      clients, however, that for whatever reason either pick a fixed
      client port or have a very guessable one (due to the range of
      ephemeral ports available with their operating system or other
      application considerations) for such applications a spoofing
      attack becomes less difficult.

   For the purposes of the rest of this discussion we will assume that
   the attacker knows the 4-tuple values.  This assumption will help us
   focus on the effects of the window size versus the number of TCP
   packets an attacker must generate.  This assumption will rarely be
   true in the real Internet since at least the client port number will
   provide us with some amount of randomness (depending on the operating

   To successfully inject a spoofed packet (RST, SYN, or DATA), in the
   past, the entire sequence space (i.e., 2^32) was often considered
   available to make such an attack unlikely.  [SITW] demonstrated that
   this assumption was incorrect and that instead of (1/2 * 2^32)
   packets (assuming a random distribution), (1/2 * (2^32/window))

   packets are required.  In other words, the mean number of tries
   needed to inject a RST segment is (2^31/window) rather than the 2^31
   assumed before.

   Substituting numbers into this formula, we see that for a window size
   of 32,768, an average of 65,536 packets would need to be transmitted
   in order to "spoof" a TCP segment that would be acceptable to a TCP
   receiver.  A window size of 65,535 reduces this even further to
   32,768 packets.  At today's access bandwidths, an attack of that size
   is feasible.

   With rises in bandwidth to both the home and office, it can only be
   expected that the values for default window sizes will continue to
   rise in order to better take advantage of the newly available
   bandwidth.  It also needs to be noted that this attack can be
   performed in a distributed fashion in order potentially gain access
   to more bandwidth.

   As we can see from the above discussion this weakness lowers the bar
   quite considerably for likely attacks.  But there is one additional
   dependency that is the duration of the TCP connection.  A TCP
   connection that lasts only a few brief packets, as often is the case
   for web traffic, would not be subject to such an attack since the
   connection may not be established long enough for an attacker to
   generate enough traffic.  However, there is a set of applications,
   such as BGP [RFC4271], that is judged to be potentially most affected
   by this vulnerability.  BGP relies on a persistent TCP session
   between BGP peers.  Resetting the connection can result in term-
   medium unavailability due to the need to rebuild routing tables and
   route flapping; see [NISCC] for further details.

   For applications that can use the TCP MD5 option [RFC2385], such as
   BGP, that option makes the attacks described in this specification
   effectively impossible.  However, some applications or
   implementations may find that option expensive to implement.

   There are alternative protections against the threats that this
   document addresses.  For further details regarding the attacks and
   the existing techniques, please refer to [RFC4953].  It also needs to
   be emphasized that, as suggested in [TSVWG-PORT] and [RFC1948], port
   randomization and initial sequence number (ISN) randomization would
   help improve the robustness of the TCP connection against off-path

2.  Terminology

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   document are to be interpreted as described in [RFC2119].  TCP
   terminology should be interpreted as described in [RFC0793].

3.  Blind Reset Attack Using the RST Bit

3.1.  Description of the Attack

   As described in the introduction, it is possible for an attacker to
   generate a RST segment that would be acceptable to a TCP receiver by
   guessing in-window sequence numbers.  In particular [RFC0793], page
   37, states the following:

      In all states except SYN-SENT, all reset (RST) segments are
      validated by checking their SEQ-fields [sequence numbers].  A
      reset is valid if its sequence number is in the window.  In the
      SYN-SENT state (a RST received in response to an initial SYN), the
      RST is acceptable if the ACK field acknowledges the SYN.

3.2.  Mitigation

   [RFC0793] currently requires handling of a segment with the RST bit
   when in a synchronized state to be processed as follows:

      1) If the RST bit is set and the sequence number is outside the 
      current receive window (SEG.SEQ < RCV.NXT || SEG.SEQ >= RCV.NXT+
      RCV.WND), silently drop the segment.

EID 4845 (Verified) is as follows:

Section: 3.2

Original Text:

   1) If the RST bit is set and the sequence number is outside the
      current receive window (SEG.SEQ <= RCV.NXT || SEG.SEQ > RCV.NXT+
      RCV.WND), silently drop the segment.

Corrected Text:

   1) If the RST bit is set and the sequence number is outside the
      current receive window (SEG.SEQ < RCV.NXT || SEG.SEQ >= RCV.NXT+
      RCV.WND), silently drop the segment.
The condition should be the opposite of (RCV.NXT <= SEG.SEQ < RCV.NXT+RCV.WND), which is stated in the second item of the enumeration.
2) If the RST bit is set and the sequence number is acceptable, i.e., (RCV.NXT <= SEG.SEQ < RCV.NXT+RCV.WND), then reset the connection. Instead, implementations SHOULD implement the following steps in place of those specified in [RFC0793] (as listed above). 1) If the RST bit is set and the sequence number is outside the current receive window, silently drop the segment. 2) If the RST bit is set and the sequence number exactly matches the next expected sequence number (RCV.NXT), then TCP MUST reset the connection. 3) If the RST bit is set and the sequence number does not exactly match the next expected sequence value, yet is within the current receive window (RCV.NXT < SEG.SEQ < RCV.NXT+RCV.WND), TCP MUST send an acknowledgment (challenge ACK): <SEQ=SND.NXT><ACK=RCV.NXT><CTL=ACK> After sending the challenge ACK, TCP MUST drop the unacceptable segment and stop processing the incoming packet further. Further segments destined to this connection will be processed as normal. The modified RST segment processing would thus become: In all states except SYN-SENT, all reset (RST) segments are validated by checking their SEQ-fields [sequence numbers]. A reset is valid if its sequence number exactly matches the next expected sequence number. If the RST arrives and its sequence number field does NOT match the next expected sequence number but is within the window, then the receiver should generate an ACK. In all other cases, where the SEQ-field does not match and is outside the window, the receiver MUST silently discard the segment. In the SYN-SENT state (a RST received in response to an initial SYN), the RST is acceptable if the ACK field acknowledges the SYN. In all other cases the receiver MUST silently discard the segment. With the above slight change to the TCP state machine, it becomes much harder for an attacker to generate an acceptable reset segment. In cases where the remote peer did generate a RST, but it fails to meet the above criteria (the RST sequence number was within the window but NOT the exact expected sequence number), when the challenge ACK is sent back, it will no longer have the transmission control block (TCB) related to this connection and hence as per [RFC0793], the remote peer will send a second RST back. The sequence number of the second RST is derived from the acknowledgment number of the incoming ACK. This second RST, if it reaches the sender, will cause the connection to be aborted since the sequence number would now be an exact match. A valid RST received out of order would still generate a challenge ACK in response. If this RST happens to be a genuine one, the other end would send an RST with an exact sequence number match that would cause the connection to be dropped. Note that the above mitigation may cause a non-amplification ACK exchange. This concern is discussed in Section 10. 4. Blind Reset Attack Using the SYN Bit 4.1. Description of the Attack The analysis of the reset attack using the RST bit highlights another possible avenue for a blind attacker using a similar set of sequence number guessing. Instead of using the RST bit, an attacker can use the SYN bit with the exact same semantics to tear down a connection. 4.2. Mitigation [RFC0793] currently requires handling of a segment with the SYN bit set in the synchronized state to be as follows: 1) If the SYN bit is set and the sequence number is outside the expected window, send an ACK back to the sender. 2) If the SYN bit is set and the sequence number is acceptable, i.e., (RCV.NXT <= SEG.SEQ < RCV.NXT+RCV.WND), then send a RST segment to the sender. Instead, the handling of the SYN in the synchronized state SHOULD be performed as follows: 1) If the SYN bit is set, irrespective of the sequence number, TCP MUST send an ACK (also referred to as challenge ACK) to the remote peer: <SEQ=SND.NXT><ACK=RCV.NXT><CTL=ACK> After sending the acknowledgment, TCP MUST drop the unacceptable segment and stop processing further. By sending an ACK, the remote peer is challenged to confirm the loss of the previous connection and the request to start a new connection. A legitimate peer, after restart, would not have a TCB in the synchronized state. Thus, when the ACK arrives, the peer should send a RST segment back with the sequence number derived from the ACK field that caused the RST. This RST will confirm that the remote peer has indeed closed the previous connection. Upon receipt of a valid RST, the local TCP endpoint MUST terminate its connection. The local TCP endpoint should then rely on SYN retransmission from the remote end to re-establish the connection. A spoofed SYN, on the other hand, will then have generated an additional ACK that the peer will discard as a duplicate ACK and will not affect the established connection. Note that this mitigation does leave one corner case un-handled, which will prevent the reset of a connection when it should be reset (i.e., it is a non-spoofed SYN wherein a peer really did restart). This problem occurs when the restarting host chooses the exact same IP address and port number that it was using prior to its restart. By chance, the restarted host must also choose an initial sequence number of exactly (RCV.NXT - 1) of the remote peer that is still in the established state. Such a case would cause the receiver to generate a "challenge" ACK as described above. But since the ACK would be within the outgoing connections window, the inbound ACK would be acceptable, and the sender of the SYN will do nothing with the response ACK. This sequence will continue as the SYN sender continually times out and retransmits the SYN until such time as the connection attempt fails. This corner case is a result of the [RFC0793] specification and is not introduced by these new requirements. Note that the above mitigation may cause a non-amplification ACK exchange. This concern is discussed in Section 10. 5. Blind Data Injection Attack 5.1. Description of the Attack A third type of attack is also highlighted by both the RST and SYN attacks. It is also possible to inject data into a TCP connection by simply guessing a sequence number within the current receive window of the victim. The ACK value of any data segment is considered valid as long as it does not acknowledge data ahead of the next segment to send. In other words, an ACK value is acceptable if it is ((SND.UNA-(2^31-1)) <= SEG.ACK <= SND.NXT). The (2^31 - 1) in the above inequality takes into account the fact that comparisons on TCP sequence and acknowledgment numbers is done using the modulo 32-bit arithmetic to accommodate the number wraparound. This means that an attacker has to guess two ACK values with every guessed sequence number so that the chances of successfully injecting data into a connection are 1 in ( 1/2 (2^32 / RCV.WND) * 2). Thus, the mean number of tries needed to inject data successfully is 1/2 (2*2^32/RWND) = 2^32/RCV.WND. When an attacker successfully injects data into a connection, the data will sit in the receiver's re-assembly queue until the peer sends enough data to bridge the gap between the RCV.NXT value and the injected data. At that point, one of two things will occur: 1) A packet war will ensue with the receiver indicating that it has received data up until RCV.NXT (which includes the attacker's data) and the sender sending an ACK with an acknowledgment number less than RCV.NXT. 2) The sender will send enough data to the peer that will move RCV.NXT even further along past the injected data. Depending upon the TCP implementation in question and the TCP traffic characteristics at that time, data corruption may result. In case (a), the connection will eventually be reset by one of the sides unless the sender produces more data that will transform the ACK war into case (b). The reset will usually occur via User Time Out (UTO) (see section of [RFC1122]). Note that the protections illustrated in this section neither cause an ACK war nor prevent one from occurring if data is actually injected into a connection. The ACK war is a product of the attack itself and cannot be prevented (other than by preventing the data from being injected). 5.2. Mitigation All TCP stacks MAY implement the following mitigation. TCP stacks that implement this mitigation MUST add an additional input check to any incoming segment. The ACK value is considered acceptable only if it is in the range of ((SND.UNA - MAX.SND.WND) <= SEG.ACK <= SND.NXT). All incoming segments whose ACK value doesn't satisfy the above condition MUST be discarded and an ACK sent back. It needs to be noted that RFC 793 on page 72 (fifth check) says: "If the ACK is a duplicate (SEG.ACK < SND.UNA), it can be ignored. If the ACK acknowledges something not yet sent (SEG.ACK > SND.NXT) then send an ACK, drop the segment, and return". The "ignored" above implies that the processing of the incoming data segment continues, which means the ACK value is treated as acceptable. This mitigation makes the ACK check more stringent since any ACK < SND.UNA wouldn't be accepted, instead only ACKs that are in the range ((SND.UNA - MAX.SND.WND) <= SEG.ACK <= SND.NXT) get through. A new state variable MAX.SND.WND is defined as the largest window that the local sender has ever received from its peer. This window may be scaled to a value larger than 65,535 bytes ([RFC1323]). This small check will reduce the vulnerability to an attacker guessing a valid sequence number, since, not only one must guess the in-window sequence number, but also guess a proper ACK value within a scoped range. This mitigation reduces, but does not eliminate, the ability to generate false segments. It does however reduce the probability that invalid data will be injected. Implementations can also chose to hard code the MAX.SND.WND value to the maximum permissible window size, i.e., 65535 in the absence of window scaling. In the presence of the window scaling option, the value becomes (MAX.SND.WND << Snd.Wind.Scale). This mitigation also helps in improving robustness on accepting spoofed FIN segments (FIN attacks). Among other things, this mitigation requires that the attacker also needs to get the acknowledgment number to fall in the range mentioned above in order to successfully spoof a FIN segment leading to the closure of the connection. Thus, this mitigation greatly improves the robustness to spoofed FIN segments. Note that the above mitigation may cause a non-amplification ACK exchange. This concern is discussed in Section 10. 6. Suggested Mitigation Strengths As described in the above sections, recommendation levels for RST, SYN, and DATA are tagged as SHOULD, SHOULD, and MAY, respectively. The reason that DATA mitigation is tagged as MAY, even though it increased the TCP robustness in general is because, the DATA injection is perceived to be more difficult (twice as unlikely) when compared to RST and SYN counterparts. However, it needs to be noted that all the suggested mitigations improve TCP's robustness in general and hence the choice of implementing some or all mitigations recommended in the document is purely left to the implementer. 7. ACK Throttling In order to alleviate multiple RSTs/SYNs from triggering multiple challenge ACKs, an ACK throttling mechanism is suggested as follows: 1) The system administrator can configure the number of challenge ACKs that can be sent out in a given interval. For example, in any 5 second window, no more than 10 challenge ACKs should be sent. 2) The values for both the time and number of ACKs SHOULD be tunable by the system administrator to accommodate different perceived levels of threat and/or system resources. It should be noted that these numbers are empirical in nature and have been obtained from the RST throttling mechanisms existing in some implementations. Also, note that no timer is needed to implement the above mechanism, instead a timestamp and a counter can be used. An implementation SHOULD include an ACK throttling mechanism to be conservative. While we have not encountered a case where the lack of ACK throttling can be exploited, as a fail-safe mechanism we recommend its use. An implementation may take an excessive number of invocations of the throttling mechanism as an indication that network conditions are unusual or hostile. An administrator who is more concerned about protecting his bandwidth and CPU utilization may set smaller ACK throttling values whereas an administrator who is more interested in faster cleanup of stale connections (i.e., concerned about excess TCP state) may decide to set a higher value thus allowing more RST's to be processed in any given time period. The time limit SHOULD be tunable to help timeout brute force attacks faster than a potential legitimate flood of RSTs. 8. Backward Compatibility and Other Considerations All of the new required mitigation techniques in this document are totally compatible with existing ([RFC0793]) compliant TCP implementations as this document introduces no new assumptions or conditions. There is a corner scenario in the above mitigations that will require more than one round-trip time to successfully abort the connection as per the figure below. This scenario is similar to the one in which the original RST was lost in the network. TCP A TCP B 1.a. ESTAB <-- <SEQ=300><ACK=101><CTL=ACK><DATA> <-- ESTAB b. (delayed) ... <SEQ=400><ACK=101><CTL=ACK><DATA> <-- ESTAB c. (in flight) ... <SEQ=500><ACK=101><CTL=RST> <-- CLOSED 2. ESTAB --> <SEQ=101><ACK=400><CTL=ACK> --> CLOSED (ACK for 1.a) ... <SEQ=400><ACK=0><CTL=RST> <-- CLOSED 3. CHALLENGE --> <SEQ=101><ACK=400><CTL=ACK> --> CLOSED (for 1.c) ... <SEQ=400><ACK=0><CTL=RST> <-- RESPONSE 4.a. ESTAB <-- <SEQ=400><ACK=101><CTL=ACK><DATA> 1.b reaches A b. ESTAB --> <SEQ=101><ACK=500><CTL=ACK> c. (in flight) ... <SEQ=500><ACK=0><CTL=RST> <-- CLOSED 5. RESPONSE arrives at A, but dropped since its outside of window. 6. ESTAB <-- <SEQ=500><ACK=0><CTL=RST> 4.c reaches A 7. CLOSED CLOSED For the mitigation to be maximally effective against the vulnerabilities discussed in this document, both ends of the TCP connection need to have the fix. Although, having the mitigations at one end might prevent that end from being exposed to the attack, the connection is still vulnerable at the other end. 9. Middlebox Considerations 9.1. Middlebox That Resend RSTs Consider a middlebox M-B tracking connections between two TCP end hosts E-A and E-C. If E-C sends a RST with a sequence number that is within the window but not an exact match to reset the connection and M-B does not have the fix recommended in this document, it may clear the connection and forward the RST to E-A saving an incorrect sequence number. If E-A does not have the fix, the connection would get cleared as required. However, if E-A does have the required fix, it will send a challenge ACK to E-C. M-B, being a middlebox, may intercept this ACK and resend the RST on behalf of E-C with the old sequence number. This RST will, again, not be acceptable and may trigger a challenge ACK. The above situation may result in a RST/ACK war. However, we believe that if such a case exists in the Internet, the middlebox is generating packets a conformant TCP endpoint would not generate. [RFC0793] dictates that the sequence number of a RST has to be derived from the acknowledgment number of the incoming ACK segment. It is outside the scope of this document to suggest mitigations to the ill-behaved middleboxes. Consider a similar scenario where the RST from M-B to E-A gets lost, E-A will continue to hold the connection and E-A might send an ACK an arbitrary time later after the connection state was destroyed at M-B. For this case, M-B will have to cache the RST for an arbitrary amount of time until it is confirmed that the connection has been cleared at E-A. 9.2. Middleboxes That Advance Sequence Numbers Some middleboxes may compute RST sequence numbers at the higher end of the acceptable window. The scenario is the same as the earlier case, but in this case instead of sending the cached RST, the middlebox (M-B) sends a RST that computes its sequence number as the sum of the acknowledgment field in the ACK and the window advertised by the ACK that was sent by E-A to challenge the RST as depicted below. The difference in the sequence numbers between step 1 and 2 below is due to data lost in the network. TCP A Middlebox 1. ESTABLISHED <-- <SEQ=500><ACK=100><CTL=RST> <-- CLOSED 2. ESTABLISHED --> <SEQ=100><ACK=300><WND=500><CTL=ACK> --> CLOSED 3. ESTABLISHED <-- <SEQ=800><ACK=100><CTL=RST> <-- CLOSED 4. ESTABLISHED --> <SEQ=100><ACK=300><WND=500><CTL=ACK> --> CLOSED 5. ESTABLISHED <-- <SEQ=800><ACK=100><CTL=RST> <-- CLOSED Although the authors are not aware of an implementation that does the above, it could be mitigated by implementing the ACK throttling mechanism described earlier. 9.3. Middleboxes That Drop the Challenge ACK It also needs to be noted that, some middleboxes (Firewalls/NATs) that don't have the fix recommended in the document, may drop the challenge ACK. This can happen because, the original RST segment that was in window had already cleared the flow state pertaining to the TCP connection in the middlebox. In such cases, the end hosts that have implemented the RST mitigation described in this document, will have the TCP connection left open. This is a corner case and can go away if the middlebox is conformant with the changes proposed in this document. 10. Security Considerations These changes to the TCP state machine do NOT protect an implementation from on-path attacks. It also needs to be emphasized that while mitigations within this document make it harder for off- path attackers to inject segments, it does NOT make it impossible. The only way to fully protect a TCP connection from both on- and off- path attacks is by using either IPsec Authentication Header (AH) [RFC4302] or IPsec Encapsulating Security Payload (ESP) [RFC4303]. Implementers also should be aware that the attacks detailed in this specification are not the only attacks available to an off-path attacker and that the counter measures described herein are not a comprehensive defense against such attacks. In particular, administrators should be aware that forged ICMP messages provide off-path attackers the opportunity to disrupt connections or degrade service. Such attacks may be subject to even less scrutiny than the TCP attacks addressed here, especially in stacks not tuned for hostile environments. It is important to note that some ICMP messages, validated or not, are key to the proper function of TCP. Those ICMP messages used to properly set the path maximum transmission unit are the most obvious example. There are a variety of ways to choose which, if any, ICMP messages to trust in the presence of off-path attackers and choosing between them depends on the assumptions and guarantees developers and administrators can make about their network. This specification does not attempt to do more than note this and related issues. Unless implementers address spoofed ICMP messages [RFC5927], the mitigations specified in this document may not provide the desired protection level. In any case, this RFC details only part of a complete strategy to prevent off-path attackers from disrupting services that use TCP. Administrators and implementers should consider the other attack vectors and determine appropriate mitigations in securing their systems. Another notable consideration is that a reflector attack is possible with the required RST/SYN mitigation techniques. In this attack, an off-path attacker can cause a victim to send an ACK segment for each spoofed RST/SYN segment that lies within the current receive window of the victim. It should be noted, however, that this does not cause any amplification since the attacker must generate a segment for each one that the victim will generate. 11. Contributors Mitesh Dalal and Amol Khare of Cisco Systems came up with the solution for the RST/SYN attacks. Anantha Ramaiah and Randall Stewart of Cisco Systems discovered the data injection vulnerability and together with Patrick Mahan and Peter Lei of Cisco Systems found solutions for the same. Paul Goyette, Mark Baushke, Frank Kastenholz, Art Stine, and David Wang of Juniper Networks provided the insight that apart from RSTs, SYNs could also result in formidable attacks. Shrirang Bage of Cisco Systems, Qing Li and Preety Puri of Wind River Systems, and Xiaodan Tang of QNX Software along with the folks above helped in ratifying and testing the interoperability of the suggested solutions. 12. Acknowledgments Special thanks to Mark Allman, Ted Faber, Steve Bellovin, Vern Paxson, Allison Mankin, Sharad Ahlawat, Damir Rajnovic, John Wong, Joe Touch, Alfred Hoenes, Andre Oppermann, Fernando Gont, Sandra Murphy, Brian Carpenter, Cullen Jennings, and other members of the tcpm WG for suggestions and comments. ACK throttling was introduced to this document by combining the suggestions from the tcpm working group. 13. References 13.1. Normative References [RFC0793] Postel, J., "Transmission Control Protocol", STD 7, RFC 793, September 1981. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. 13.2. Informative References [Medina05] Medina, A., Allman, M., and S. Floyd, "Measuring the Evolution of Transport Protocols in the Internet", ACM Computer Communication Review, 35(2), April 2005, <>. [NISCC] NISCC, "NISCC Vulnerability Advisory 236929 - Vulnerability Issues in TCP". [RFC1122] Braden, R., "Requirements for Internet Hosts - Communication Layers", STD 3, RFC 1122, October 1989. [RFC1323] Jacobson, V., Braden, B., and D. Borman, "TCP Extensions for High Performance", RFC 1323, May 1992. [RFC1948] Bellovin, S., "Defending Against Sequence Number Attacks", RFC 1948, May 1996. [RFC2385] Heffernan, A., "Protection of BGP Sessions via the TCP MD5 Signature Option", RFC 2385, August 1998. [RFC4271] Rekhter, Y., Li, T., and S. Hares, "A Border Gateway Protocol 4 (BGP-4)", RFC 4271, January 2006. [RFC4302] Kent, S., "IP Authentication Header", RFC 4302, December 2005. [RFC4303] Kent, S., "IP Encapsulating Security Payload (ESP)", RFC 4303, December 2005. [RFC4953] Touch, J., "Defending TCP Against Spoofing Attacks", RFC 4953, July 2007. [RFC5927] Gont, F., "ICMP Attacks against TCP", RFC 5927, July 2010. [SITW] Watson, P., "Slipping in the Window: TCP Reset attacks", Presentation at 2004 CanSecWest, <>. [TSVWG-PORT] Larsen, M. and F. Gont, "Transport Protocol Port Randomization Recommendations", Work in Progress, August 2010. Authors' Addresses Anantha Ramaiah Cisco Systems 170 Tasman Drive San Jose, CA 95134 USA Phone: +1 (408) 525-6486 EMail: Randall R. Stewart Huawei 148 Crystal Cove Ct Chapin, SC 29036 USA Phone: +1 (803) 345-0369 EMail: Mitesh Dalal Cisco Systems 170 Tasman Drive San Jose, CA 95134 USA Phone: +1 (408) 853-5257 EMail: