Network Working Group                                         K. Nichols
Request for Comments: 3086                                 Packet Design
Category: Informational                                     B. Carpenter
                                                              April 2001

       Definition of Differentiated Services Per Domain Behaviors
                   and Rules for their Specification

Status of this Memo

   This memo provides information for the Internet community.  It does
   not specify an Internet standard of any kind.  Distribution of this
   memo is unlimited.

Copyright Notice

   Copyright (C) The Internet Society (2001).  All Rights Reserved.


   The differentiated services framework enables quality-of-service
   provisioning within a network domain by applying rules at the edges
   to create traffic aggregates and coupling each of these with a
   specific forwarding path treatment in the domain through use of a
   codepoint in the IP header.  The diffserv WG has defined the general
   architecture for differentiated services and has focused on the
   forwarding path behavior required in routers, known as "per-hop
   forwarding behaviors" (or PHBs).  The WG has also discussed
   functionality required at diffserv (DS) domain edges to select
   (classifiers) and condition (e.g., policing and shaping) traffic
   according to the rules.  Short-term changes in the QoS goals for a DS
   domain are implemented by changing only the configuration of these
   edge behaviors without necessarily reconfiguring the behavior of
   interior network nodes.

   The next step is to formulate examples of how forwarding path
   components (PHBs, classifiers, and traffic conditioners) can be used
   to compose traffic aggregates whose packets experience specific
   forwarding characteristics as they transit a differentiated services
   domain.  The WG has decided to use the term per-domain behavior, or
   PDB, to describe the behavior experienced by a particular set of
   packets as they cross a DS domain.  A PDB is characterized by
   specific metrics that quantify the treatment a set of packets with a
   particular DSCP (or set of DSCPs) will receive as it crosses a DS
   domain.  A PDB specifies a forwarding path treatment for a traffic
   aggregate and, due to the role that particular choices of edge and

Nichols & Carpenter          Informational                      [Page 1]

RFC 3086             Diffserv per Domain Behaviors            April 2001

   PHB configuration play in its resulting attributes, it is where the
   forwarding path and the control plane interact.  The measurable
   parameters of a PDB should be suitable for use in Service Level
   Specifications at the network edge.

   This document defines and discusses Per-Domain Behaviors in detail
   and lays out the format and required content for contributions to the
   Diffserv WG on PDBs and the procedure that will be applied for
   individual PDB specifications to advance as WG products.  This format
   is specified to expedite working group review of PDB submissions.

Table of Contents

    1. Introduction ................................................ 2
    2. Definitions ................................................. 4
    3. The Value of Defining Edge-to-Edge Behavior ................. 5
    4. Understanding PDBs .......................................... 7
    5. Format for Specification of Diffserv Per-Domain Behaviors ...13
    6. On PDB Attributes ...........................................16
    7. A Reference Per-Domain Behavior .............................19
    8. Guidelines for Advancing PDB Specifications .................21
    9. Security Considerations .....................................22
   10. Acknowledgements ............................................22
       References ..................................................22
       Authors' Addresses ..........................................23
       Full Copyright Statement ....................................24

1 Introduction

   Differentiated Services allows an approach to IP Quality of Service
   that is modular, incrementally deployable, and scalable while
   introducing minimal per-node complexity [RFC2475].  From the end
   user's point of view, QoS should be supported end-to-end between any
   pair of hosts.  However, this goal is not immediately attainable.  It
   will require interdomain QoS support, and many untaken steps remain
   on the road to achieving this.  One essential step, the evolution of
   the business models for interdomain QoS, will necessarily develop
   outside of the IETF.  A goal of the diffserv WG is to provide the
   firm technical foundation that allows these business models to
   develop.  The first major step will be to support edge-to-edge or
   intradomain QoS between the ingress and egress of a single network,
   i.e., a DS Domain in the terminology of RFC 2474.  The intention is
   that this edge-to-edge QoS should be composable, in a purely
   technical sense, to a quantifiable QoS across a DS Region composed of
   multiple DS domains.

Nichols & Carpenter          Informational                      [Page 2]

RFC 3086             Diffserv per Domain Behaviors            April 2001

   The Diffserv WG has finished the first phase of standardizing the
   behaviors required in the forwarding path of all network nodes, the
   per-hop forwarding behaviors or PHBs.  The PHBs defined in RFCs 2474,
   2597 and 2598 give a rich toolbox for differential packet handling by
   individual boxes.  The general architectural model for diffserv has
   been documented in RFC 2475.  An informal router model [MODEL]
   describes a model of traffic conditioning and other forwarding
   behaviors.  However, technical issues remain in moving "beyond the
   box" to intradomain QoS models.

   The ultimate goal of creating scalable end-to-end QoS in the Internet
   requires that we can identify and quantify behavior for a group of
   packets that is preserved when they are aggregated with other packets
   as they traverse the Internet.  The step of specifying forwarding
   path attributes on a per-domain basis for a set of packets
   distinguished only by the mark in the DS field of individual packets
   is critical in the evolution of Diffserv QoS and should provide the
   technical input that will aid in the construction of business models.
   This document defines and specifies the term "Per-Domain Behavior" or
   PDB to describe QoS attributes across a DS domain.

   Diffserv classification and traffic conditioning are applied to
   packets arriving at the boundary of a DS domain to impose
   restrictions on the composition of the resultant traffic aggregates,
   as distinguished by the DSCP marking , inside the domain.  The
   classifiers and traffic conditioners are set to reflect the policy
   and traffic goals for that domain and may be specified in a TCA
   (Traffic Conditioning Agreement).  Once packets have crossed the DS
   boundary, adherence to diffserv principles makes it possible to group
   packets solely according to the behavior they receive at each hop (as
   selected by the DSCP).  This approach has well-known scaling
   advantages, both in the forwarding path and in the control plane.
   Less well recognized is that these scaling properties only result if
   the per-hop behavior definition gives rise to a particular type of
   invariance under aggregation.  Since the per-hop behavior must be
   equivalent for every node in the domain, while the set of packets
   marked for that PHB may be different at every node, PHBs should be
   defined such that their characteristics do not depend on the traffic
   volume of the associated BA on a router's ingress link nor on a
   particular path through the DS domain taken by the packets.
   Specifically, different streams of traffic that belong to the same
   traffic aggregate merge and split as they traverse the network.  If
   the properties of a PDB using a particular PHB hold regardless of how
   the temporal characteristics of the marked traffic aggregate change
   as it traverses the domain, then that PDB scales.  (Clearly this
   assumes that numerical parameters such as bandwidth allocated to the
   particular PDB may be different at different points in the network,
   and may be adjusted dynamically as traffic volume varies.)  If there

Nichols & Carpenter          Informational                      [Page 3]

RFC 3086             Diffserv per Domain Behaviors            April 2001

   are limits to where the properties hold, that translates to a limit
   on the size or topology of a DS domain that can use that PDB.
   Although useful single-link DS domains might exist, PDBs that are
   invariant with network size or that have simple relationships with
   network size and whose properties can be recovered by reapplying
   rules (that is, forming another diffserv boundary or edge to re-
   enforce the rules for the traffic aggregate) are needed for building
   scalable end-to-end quality of service.

   There is a clear distinction between the definition of a Per-Domain
   Behavior in a DS domain and a service that might be specified in a
   Service Level Agreement.  The PDB definition is a technical building
   block that permits the coupling of classifiers, traffic conditioners,
   specific PHBs, and particular configurations with a resulting set of
   specific observable attributes which may be characterized in a
   variety of ways.  These definitions are intended to be useful tools
   in configuring DS domains, but the PDB (or PDBs) used by a provider
   is not expected to be visible to customers any more than the specific
   PHBs employed in the provider's network would be.  Network providers
   are expected to select their own measures to make customer-visible in
   contracts and these may be stated quite differently from the
   technical attributes specified in a PDB definition, though the
   configuration of a PDB might be taken from a Service Level
   Specification (SLS).  Similarly, specific PDBs are intended as tools
   for ISPs to construct differentiated services offerings; each may
   choose different sets of tools, or even develop their own, in order
   to achieve particular externally observable metrics.  Nevertheless,
   the measurable parameters of a PDB are expected to be among the
   parameters cited directly or indirectly in the Service Level
   Specification component of a corresponding SLA.

   This document defines Differentiated Services Per-Domain Behaviors
   and specifies the format that must be used for submissions of
   particular PDBs to the Diffserv WG.

2 Definitions

   The following definitions are stated in RFCs 2474 and 2475 and are
   repeated here for easy reference:

   " Behavior Aggregate: a collection of packets with the same codepoint
     crossing a link in a particular direction.

   " Differentiated Services Domain: a contiguous portion of the
     Internet over which a consistent set of differentiated services
     policies are administered in a coordinated fashion.  A
     differentiated services domain can represent different

Nichols & Carpenter          Informational                      [Page 4]

RFC 3086             Diffserv per Domain Behaviors            April 2001

     administrative domains or autonomous systems, different trust
     regions, different network technologies (e.g., cell/frame), hosts
     and routers, etc.  Also DS domain.

   " Differentiated Services Boundary: the edge of a DS domain, where
     classifiers and traffic conditioners are likely to be deployed.  A
     differentiated services boundary can be further sub-divided into
     ingress and egress nodes, where the ingress/egress nodes are the
     downstream/upstream nodes of a boundary link in a given traffic
     direction.  A differentiated services boundary typically is found
     at the ingress to the first-hop differentiated services-compliant
     router (or network node) that a host's packets traverse, or at the
     egress of the last-hop differentiated services-compliant router or
     network node that packets traverse before arriving at a host.  This
     is sometimes referred to as the boundary at a leaf router.  A
     differentiated services boundary may be co-located with a host,
     subject to local policy.  Also DS boundary.

   To these we add:

   " Traffic Aggregate: a collection of packets with a codepoint that
     maps to the same PHB, usually in a DS domain or some subset of a DS
     domain.  A traffic aggregate marked for the foo PHB is referred to
     as the "foo traffic aggregate" or "foo aggregate" interchangeably.
     This generalizes the concept of Behavior Aggregate from a link to a

   " Per-Domain Behavior: the expected treatment that an identifiable or
     target group of packets will receive from "edge-to-edge" of a DS
     domain.  (Also PDB.)  A particular PHB (or, if applicable, list of
     PHBs) and traffic conditioning requirements are associated with
     each PDB.

   " A Service Level Specification (SLS) is a set of parameters and
     their values which together define the service offered to a traffic
     stream by a DS domain.  It is expected to include specific values
     or bounds for PDB parameters.

3 The Value of Defining Edge-to-Edge Behavior

   As defined in section 2, a PDB describes the edge-to-edge behavior
   across a DS domain's "cloud." Specification of the transit
   expectations of packets matching a target for a particular diffserv
   behavior across a DS domain will both assist in the deployment of
   single-domain QoS and will help enable the composition of end-to-end,
   cross-domain services.  Networks of DS domains can be connected to
   create end-to-end services by building on the PDB characteristics
   without regard to the particular PHBs used.  This level of

Nichols & Carpenter          Informational                      [Page 5]

RFC 3086             Diffserv per Domain Behaviors            April 2001

   abstraction makes it easier to compose cross-domain services as well
   as making it possible to hide details of a network's internals while
   exposing information sufficient to enable QoS.

   Today's Internet is composed of multiple independently administered
   domains or Autonomous Systems (ASs), represented by the "clouds" in
   figure 1.  To deploy ubiquitous end-to-end quality of service in the
   Internet, business models must evolve that include issues of charging
   and reporting that are not in scope for the IETF.  In the meantime,
   there are many possible uses of quality of service within an AS and
   the IETF can address the technical issues in creating an intradomain
   QoS within a Differentiated Services framework.  In fact, this
   approach is quite amenable to incremental deployment strategies.

   Where DS domains are independently administered, the evolution of the
   necessary business agreements and future signaling arrangements will
   take some time, thus, early deployments will be within a single
   administrative domain.  Putting aside the business issues, the same
   technical issues that arise in interconnecting DS domains with
   homogeneous administration will arise in interconnecting the
   autonomous systems (ASs) of the Internet.

                 |                AS2                   |
                 |                                      |
    -------      |     ------------     ------------    |
    | AS1 |------|-----X           |    |          |    |
    -------      |     |           |    Y          |    |        -------
                 |     |           |   /|          X----|--------| AS3 |
                 |     |           |  / |          |    |        -------
                 |     |           | /  ------------    |
                 |     |           Y      |             |
                 |     |           | \  ------------    |
    -------      |     |           |  \ |          |    |
    | AS4 |------|-----X           |   \|          |    |
    -------      |     |           |    Y          X----|------
                 |     |           |    |          |    |
                 |     ------------     ------------    |
                 |                                      |
                 |                                      |

         Figure 1: Interconnection of ASs and DS Domains

   A single AS (e.g., AS2 in figure 1) may be composed of subnetworks
   and, as the definition allows, these can be separate DS domains.  An
   AS might have multiple DS domains for a number of reasons, most
   notable being to follow topological and/or technological boundaries

Nichols & Carpenter          Informational                      [Page 6]

RFC 3086             Diffserv per Domain Behaviors            April 2001

   and to separate the allocation of resources.  If we confine ourselves
   to the DS boundaries between these "interior" DS domains, we avoid
   the non-technical problems of setting up a service and can address
   the issues of creating characterizable PDBs.

   The incentive structure for differentiated services is based on
   upstream domains ensuring their traffic conforms to the Traffic
   Conditioning Agreements (TCAs) with downstream domains and downstream
   domains enforcing that TCA, thus metrics associated with PDBs can be
   sensibly computed.  The letters "X" and "Y" in figure 1 represent the
   DS boundary routers containing traffic conditioners that ensure and
   enforce conformance (e.g., shapers and policers).  Although policers
   and shapers are expected at the DS boundaries of ASs (the "X" boxes),
   they might appear anywhere, or nowhere, inside the AS.  Specifically,
   the boxes at the DS boundaries internal to the AS (the "Y" boxes) may
   or may not condition traffic.  Technical guidelines for the placement
   and configuration of DS boundaries should derive from the attributes
   of a particular PDB under aggregation and multiple hops.

   This definition of PDB continues the separation of forwarding path
   and control plane described in RFC 2474.  The forwarding path
   characteristics are addressed by considering how the behavior at
   every hop of a packet's path is affected by the merging and branching
   of traffic aggregates through multiple hops.  Per-hop behaviors in
   nodes are configured infrequently, representing a change in network
   infrastructure.  More frequent quality-of-service changes come from
   employing control plane functions in the configuration of the DS
   boundaries.  A PDB provides a link between the DS domain level at
   which control is exercised to form traffic aggregates with quality-
   of-service goals across the domain and the per-hop and per-link
   treatments packets receive that results in meeting the quality-of-
   service goals.

4 Understanding PDBs

4.1 Defining PDBs

   RFCs 2474 and 2475 define a Differentiated Services Behavior
   Aggregate as "a collection of packets with the same DS codepoint
   crossing a link in a particular direction" and further state that
   packets with the same DSCP get the same per-hop forwarding treatment
   (or PHB) everywhere inside a single DS domain.  Note that even if
   multiple DSCPs map to the same PHB, this must hold for each DSCP
   individually.  In section 2 of this document, we introduced a more
   general definition of a traffic aggregate in the diffserv sense so
   that we might easily refer to the packets which are mapped to the
   same PHB everywhere within a DS domain.  Section 2 also presented a
   short definition of PDBs which we expand upon in this section:

Nichols & Carpenter          Informational                      [Page 7]

RFC 3086             Diffserv per Domain Behaviors            April 2001

   Per-Domain Behavior: the expected treatment that an identifiable or
     target group of packets will receive from "edge to edge" of a DS
     domain.  A particular PHB (or, if applicable, list of PHBs) and
     traffic conditioning requirements are associated with each PDB.

   Each PDB has measurable, quantifiable, attributes that can be used to
   describe what happens to its packets as they enter and cross the DS
   domain.  These derive from the characteristics of the traffic
   aggregate that results from application of classification and traffic
   conditioning during the entry of packets into the DS domain and the
   forwarding treatment (PHB) the packets get inside the domain, but can
   also depend on the entering traffic loads and the domain's topology.
   PDB attributes may be absolute or statistical and they may be
   parameterized by network properties.  For example, a loss attribute
   might be expressed as "no more than 0.1% of packets will be dropped
   when measured over any time period larger than T", a delay attribute
   might be expressed as "50% of delivered packets will see less than a
   delay of d milliseconds, 30% will see a delay less than 2d ms, 20%
   will see a delay of less than 3d ms." A wide range of metrics is
   possible.  In general they will be expressed as bounds or percentiles
   rather than as absolute values.

   A PDB is applied to a target group of packets arriving at the edge of
   the DS domain.  The target group is distinguished from all arriving
   packets by use of packet classifiers [RFC2475] (where the classifier
   may be "null").  The action of the PDB on the target group has two
   parts.  The first part is the the use of traffic conditioning to
   create a traffic aggregate.  During traffic conditioning, conformant
   packets are marked with a DSCP for the PHB associated with the PDB
   (see figure 2).  The second part is the treatment experienced by
   packets from the same traffic aggregate transiting the interior of a
   DS domain, between and inside of DS domain boundaries.  The following
   subsections further discuss these two effects on the target group
   that arrives at the DS domain boundary.

           -----------   ------------   --------------------   foo
arriving _|classifiers|_|target group|_|traffic conditioning|_ traffic
packets   |           | |of packets  | |& marking (for foo) |  aggregate
           -----------   ------------   --------------------

         Figure 2: Relationship of the traffic aggregate associated
                    with a PDB to arriving packets

Nichols & Carpenter          Informational                      [Page 8]

RFC 3086             Diffserv per Domain Behaviors            April 2001

4.1.1 Crossing the DS edge: the effects of traffic conditioning on the
      target group

   This effect is quantified by the relationship of the emerging traffic
   aggregate to the entering target group.  That relationship can depend
   on the arriving traffic pattern as well as the configuration of the
   traffic conditioners.  For example, if the EF PHB [RFC2598] and a
   strict policer of rate R are associated with the foo PDB, then the
   first part of characterizing the foo PDB is to write the relationship
   between the arriving target packets and the departing foo traffic
   aggregate.  In this case, "the rate of the emerging foo traffic
   aggregate is less than or equal to the smaller of R and the arrival
   rate of the target group of packets" and additional temporal
   characteristics of the packets (e.g., burst) may be specified as
   desired.  Thus, there is a "loss rate" on the arriving target group
   that results from sending too much traffic or the traffic with the
   wrong temporal characteristics.  This loss rate should be entirely
   preventable (or controllable) by the upstream sender conforming to
   the traffic conditioning associated with the PDB specification.

   The issue of "who is in control" of the loss (or demotion) rate helps
   to clearly delineate this component of PDB performance from that
   associated with transiting the domain.  The latter is completely
   under control of the operator of the DS domain and the former is used
   to ensure that the entering traffic aggregate conforms to the traffic
   profile to which the operator has provisioned the network.  Further,
   the effects of traffic conditioning on the target group can usually
   be expressed more simply than the effects of transiting the DS domain
   on the traffic aggregate's traffic profile.

   A PDB may also apply traffic conditioning at DS domain egress.  The
   effect of this conditioning on the overall PDB attributes would be
   treated similarly to the ingress characteristics (the authors may
   develop more text on this in the future, but it does not materially
   affect the ideas presented in this document.)

4.1.2 Crossing the DS domain: transit effects

   The second component of PDB performance is the metrics that
   characterize the transit of a packet of the PDB's traffic aggregate
   between any two edges of the DS domain boundary shown in figure 3.
   Note that the DS domain boundary runs through the DS boundary routers
   since the traffic aggregate is generally formed in the boundary
   router before the packets are queued and scheduled for output.  (In
   most cases, this distinction is expected to be important.)

Nichols & Carpenter          Informational                      [Page 9]

RFC 3086             Diffserv per Domain Behaviors            April 2001

   DSCPs should not change in the interior of a DS domain as there is no
   traffic conditioning being applied.  If it is necessary to reapply
   the kind of traffic conditioning that could result in remarking,
   there should be a DS domain boundary at that point, though such an
   "interior" boundary can have "lighter weight" rules in its TCA.
   Thus, when measuring attributes between locations as indicated in
   figure 3, the DSCP at the egress side can be assumed to have held
   throughout the domain.

                               |           |
                          -----X           |
                               |           |
                               |   DS      |
                               |   domain  X----
                               |           |
                          -----X           |
                               |           |

          Figure 3: Range of applicability of attributes of a traffic
                    aggregate associated with a PDB (is between the
                    points marked "X")

   Though a DS domain may be as small as a single node, more complex
   topologies are expected to be the norm, thus the PDB definition must
   hold as its traffic aggregate is split and merged on the interior
   links of a DS domain.  Packet flow in a network is not part of the
   PDB definition; the application of traffic conditioning as packets
   enter the DS domain and the consistent PHB through the DS domain must
   suffice.  A PDB's definition does not have to hold for arbitrary
   topologies of networks, but the limits on the range of applicability
   for a specific PDB must be clearly specified.

   In general, a PDB operates between N ingress points and M egress
   points at the DS domain boundary.  Even in the degenerate case where
   N=M=1, PDB attributes are more complex than the definition of PHB
   attributes since the concatenation of the behavior of intermediate
   nodes affects the former.  A complex case with N and M both greater
   than one involves splits and merges in the traffic path and is non-
   trivial to analyze.  Analytic, simulation, and experimental work will
   all be necessary to understand even the simplest PDBs.

4.2 Constructing PDBs

   A DS domain is configured to meet the network operator's traffic
   engineering goals for the domain independently of the performance
   goals for a particular flow of a traffic aggregate.  Once the

Nichols & Carpenter          Informational                     [Page 10]

RFC 3086             Diffserv per Domain Behaviors            April 2001

   interior routers are configured for the number of distinct traffic
   aggregates that the network will handle, each PDB's allocation at the
   edge comes from meeting the desired performance goals for the PDB's
   traffic aggregate subject to that configuration of packet schedulers
   and bandwidth capacity.  The configuration of traffic conditioners at
   the edge may be altered by provisioning or admission control but the
   decision about which PDB to use and how to apply classification and
   traffic conditioning comes from matching performance to goals.

   For example, consider the DS domain of figure 3.  A PDB with an
   explicit bound on loss must apply traffic conditioning at the
   boundary to ensure that on the average no more packets are admitted
   than can emerge.  Though, queueing internal to the network may result
   in a difference between input and output traffic over some
   timescales, the averaging timescale should not exceed what might be
   expected for reasonably sized buffering inside the network.  Thus if
   bursts are allowed to arrive into the interior of the network, there
   must be enough capacity to ensure that losses don't exceed the bound.
   Note that explicit bounds on the loss level can be particularly
   difficult as the exact way in which packets merge inside the network
   affects the burstiness of the PDB's traffic aggregate and hence,

   PHBs give explicit expressions of the treatment a traffic aggregate
   can expect at each hop.  For a PDB, this behavior must apply to
   merging and diverging traffic aggregates, thus characterizing a PDB
   requires understanding what happens to a PHB under aggregation.  That
   is, PHBs recursively applied must result in a known behavior.  As an
   example, since maximum burst sizes grow with the number of microflows
   or traffic aggregate streams merged, a PDB specification must address
   this.  A clear advantage of constructing behaviors that aggregate is
   the ease of concatenating PDBs so that the associated traffic
   aggregate has known attributes that span interior DS domains and,
   eventually, farther.  For example, in figure 1 assume that we have
   configured the foo PDB on the interior DS domains of AS2.  Then
   traffic aggregates associated with the foo PDB in each interior DS
   domain of AS2 can be merged at the shaded interior boundary routers.
   If the same (or fewer) traffic conditioners as applied at the
   entrance to AS2 are applied at these interior boundaries, the
   attributes of the foo PDB should continue to be used to quantify the
   expected behavior.  Explicit expressions of what happens to the
   behavior under aggregation, possibly parameterized by node in-degrees
   or network diameters, are necessary to determine what to do at the
   internal aggregation points.  One approach might be to completely
   reapply the traffic conditioning at these points; another might
   employ some limited rate-based remarking only.

Nichols & Carpenter          Informational                     [Page 11]

RFC 3086             Diffserv per Domain Behaviors            April 2001

   Multiple PDBs may use the same PHB.  The specification of a PDB can
   contain a list of PHBs and their required configuration, all of which
   would result in the same PDB.  In operation, it is expected that a
   single domain will use a single PHB to implement a particular PDB,
   though different domains may select different PHBs.  Recall that in
   the diffserv definition [RFC2474], a single PHB might be selected
   within a domain by a list of DSCPs.  Multiple PDBs might use the same
   PHB in which case the transit performance of traffic aggregates of
   these PDBs will, of necessity, be the same.  Yet, the particular
   characteristics that the PDB designer wishes to claim as attributes
   may vary, so two PDBs that use the same PHB might not be specified
   with the same list of attributes.

   The specification of the transit expectations of PDBs across domains
   both assists in the deployment of QoS within a DS domain and helps
   enable the composition of end-to-end, cross-domain services to
   proceed by making it possible to hide details of a domain's internals
   while exposing characteristics necessary for QoS.

4.3 PDBs using PHB Groups

   The use of PHB groups to construct PDBs can be done in several ways.
   A single PHB member of a PHB group might be used to construct a
   single PDB.  For example, a PDB could be defined using just one of
   the Class Selector Compliant PHBs [RFC2474].  The traffic
   conditioning for that PDB and the required configuration of the
   particular PHB would be defined in such a way that there was no
   dependence or relationship with the manner in which other PHBs of the
   group are used or, indeed, whether they are used in that DS domain.
   In this case, the reasonable approach would be to specify this PDB
   alone in a document which expressly called out the conditions and
   configuration of the Class Selector PHB required.

   A single PDB can be constructed using more than one PHB from the same
   PHB group.  For example, the traffic conditioner described in RFC
   2698 might be used to mark a particular entering traffic aggregate
   for one of the three AF1x PHBs [RFC2597] while the transit
   performance of the resultant PDB is specified, statistically, across
   all the packets marked with one of those PHBs.

   A set of related PDBs might be defined using a PHB group.  In this
   case, the related PDBs should be defined in the same document.  This
   is appropriate when the traffic conditioners that create the traffic
   aggregates associated with each PDB have some relationships and
   interdependencies such that the traffic aggregates for these PDBs
   should be described and characterized together.  The transit
   attributes will depend on the PHB associated with the PDB and will
   not be the same for all PHBs in the group, though there may be some

Nichols & Carpenter          Informational                     [Page 12]

RFC 3086             Diffserv per Domain Behaviors            April 2001

   parameterized interrelationship between the attributes of each of
   these PDBs.  In this case, each PDB should have a clearly separate
   description of its transit attributes (delineated in a separate
   subsection) within the document.  For example, the traffic
   conditioner described in RFC 2698 might be used to mark arriving
   packets for three different AF1x PHBs, each of which is to be treated
   as a separate traffic aggregate in terms of transit properties.  Then
   a single document could be used to define and quantify the
   relationship between the arriving packets and the emerging traffic
   aggregates as they relate to one another.  The transit
   characteristics of packets of each separate AF1x traffic aggregate
   should be described separately within the document.

   Another way in which a PHB group might be used to create one PDB per
   PHB might have decoupled traffic conditioners, but some relationship
   between the PHBs of the group.  For example, a set of PDBs might be
   defined using Class Selector Compliant PHBs [RFC2474] in such a way
   that the traffic conditioners that create the traffic aggregates are
   not related, but the transit performance of each traffic aggregate
   has some parametric relationship to the other.  If it makes sense to
   specify them in the same document, then the author(s) should do so.

4.4 Forwarding path vs. control plane

   A PDB's associated PHB, classifiers, and traffic conditioners are all
   in the packet forwarding path and operate at line rates.  PHBs,
   classifiers, and traffic conditioners are configured in response to
   control plane activity which takes place across a range of time
   scales, but, even at the shortest time scale, control plane actions
   are not expected to happen per-packet.  Classifiers and traffic
   conditioners at the DS domain boundary are used to enforce who gets
   to use the PDB and how the PDB should behave temporally.
   Reconfiguration of PHBs might occur monthly, quarterly, or only when
   the network is upgraded.  Classifiers and traffic conditioners might
   be reconfigured at a few regular intervals during the day or might
   happen in response to signalling decisions thousands of times a day.
   Much of the control plane work is still evolving and is outside the
   charter of the Diffserv WG.  We note that this is quite appropriate
   since the manner in which the configuration is done and the time
   scale at which it is done should not affect the PDB attributes.

5 Format for Specification of Diffserv Per-Domain Behaviors

   PDBs arise from a particular relationship between edge and interior
   (which may be parameterized).  The quantifiable characteristics of a
   PDB must be independent of whether the network edge is configured
   statically or dynamically.  The particular configuration of traffic

Nichols & Carpenter          Informational                     [Page 13]

RFC 3086             Diffserv per Domain Behaviors            April 2001

   conditioners at the DS domain edge is critical to how a PDB performs,
   but the act(s) of configuring the edge is a control plane action
   which can be separated from the specification of the PDB.

   The following sections must be present in any specification of a
   Differentiated Services PDB.  Of necessity, their length and content
   will vary greatly.

5.1 Applicability Statement

   All PDB specs must have an applicability statement that outlines the
   intended use of this PDB and the limits to its use.

5.2 Technical specification

   This section specifies the rules or guidelines to create this PDB,
   each distinguished with "may", "must" and "should." The technical
   specification must list the classification and traffic conditioning
   required (if any) and the PHB (or PHBs) to be used with any
   additional requirements on their configuration beyond that contained
   in RFCs.  Classification can reflect the results of an admission
   control process.  Traffic conditioning may include marking, traffic
   shaping, and policing.  A Service Provisioning Policy might be used
   to describe the technical specification of a particular PDB.

5.3 Attributes

   A PDB's attributes tell how it behaves under ideal conditions if
   configured in a specified manner (where the specification may be
   parameterized).  These might include drop rate, throughput, delay
   bounds measured over some time period.  They may be bounds,
   statistical bounds, or percentiles (e.g., "90% of all packets
   measured over intervals of at least 5 minutes will cross the DS
   domain in less than 5 milliseconds").  A wide variety of
   characteristics may be used but they must be explicit, quantifiable,
   and defensible.  Where particular statistics are used, the document
   must be precise about how they are to be measured and about how the
   characteristics were derived.

   Advice to a network operator would be to use these as guidelines in
   creating a service specification rather than use them directly.  For
   example, a "loss-free" PDB would probably not be sold as such, but
   rather as a service with a very small packet loss probability.

Nichols & Carpenter          Informational                     [Page 14]

RFC 3086             Diffserv per Domain Behaviors            April 2001

5.4 Parameters

   The definition and characteristics of a PDB may be parameterized by
   network-specific features; for example, maximum number of hops,
   minimum bandwidth, total number of entry/exit points of the PDB
   to/from the diffserv network, maximum transit delay of network
   elements, minimum buffer size available for the PDB at a network
   node, etc.

5.5 Assumptions

   In most cases, PDBs will be specified assuming lossless links, no
   link failures, and relatively stable routing.  This is reasonable
   since otherwise it would be very difficult to quantify behavior and
   this is the operating conditions for which most operators strive.
   However, these assumptions must be clearly stated.  Since PDBs with
   specific bandwidth parameters require that bandwidth to be available,
   the assumptions to be stated may include standby capacity.  Some PDBs
   may be specifically targeted for cases where these assumptions do not
   hold, e.g., for high loss rate links, and such targeting must also be
   made explicit.  If additional restrictions, especially specific
   traffic engineering measures, are required, these must be stated.

   Further, if any assumptions are made about the allocation of
   resources within a diffserv network in the creation of the PDB, these
   must be made explicit.

5.6 Example Uses

   A PDB specification must give example uses to motivate the
   understanding of ways in which a diffserv network could make use of
   the PDB although these are not expected to be detailed.  For example,
   "A bulk handling PDB may be used for all packets which should not
   take any resources from the network unless they would otherwise go
   unused.  This might be useful for Netnews traffic or for traffic
   rejected from some other PDB by traffic policers."

5.7 Environmental Concerns (media, topology, etc.)

   Note that it is not necessary for a provider to expose which PDB (if
   a commonly defined one) is being used nor is it necessary for a
   provider to specify a service by the PDB's attributes.  For example,
   a service provider might use a PDB with a "no queueing loss"
   characteristic in order to specify a "very low loss" service.

   This section is to inject realism into the characteristics described
   above.  Detail the assumptions made there and what constraints that
   puts on topology or type of physical media or allocation.

Nichols & Carpenter          Informational                     [Page 15]

RFC 3086             Diffserv per Domain Behaviors            April 2001

5.8 Security Considerations for each PDB

   This section should include any security considerations that are
   specific to the PDB.  Is it subject to any unusual theft-of-service
   or denial-of-service attacks?  Are any unusual security precautions

   It is not necessary to repeat the general security discussions in
   [RFC2474] and [RFC2475], but a reference should be included.  Also
   refer to any special security considerations for the PHB or PHBs

6 On PDB Attributes

   As discussed in section 4, measurable, quantifiable attributes
   associated with each PDB can be used to describe what will happen to
   packets using that PDB as they cross the domain.  In its role as a
   building block for the construction of interdomain quality-of-
   service, a PDB specification should provide the answer to the
   question: Under what conditions can we join the output of this domain
   to another under the same traffic conditioning and expectations?
   Although there are many ways in which traffic might be distributed,
   creating quantifiable, realizable PDBs that can be concatenated into
   multi-domain services limits the realistic scenarios.  A PDB's
   attributes with a clear statement of the conditions under which the
   attributes hold is critical to the composition of multi-domain

   There is a clear correlation between the strictness of the traffic
   conditioning and the quality of the PDB's attributes.  As indicated
   earlier, numerical bounds are likely to be statistical or expressed
   as a percentile.  Parameters expressed as strict bounds will require
   very precise mathematical analysis, while those expressed
   statistically can to some extent rely on experiment.  Section 7 gives
   the example of a PDB without strict traffic conditioning and
   concurrent work on a PDB with strict traffic conditioning and
   attributes is also in front of the WG [VW].  This section gives some
   general considerations for characterizing PDB attributes.

   There are two ways to characterize PDBs with respect to time.  First
   are properties over "long" time periods, or average behaviors.  A PDB
   specification should report these as the rates or throughput seen
   over some specified time period.  In addition, there are properties
   of "short" time behavior, usually expressed as the allowable
   burstiness in a traffic aggregate.  The short time behavior is
   important in understanding buffering requirements (and associated
   loss characteristics) and for metering and conditioning
   considerations at DS boundaries.  For short-time behavior, we are

Nichols & Carpenter          Informational                     [Page 16]

RFC 3086             Diffserv per Domain Behaviors            April 2001

   interested primarily in two things: 1) how many back-to-back packets
   of the PDB's traffic aggregate will we see at any point (this would
   be metered as a burst) and 2) how large a burst of packets of this
   PDB's traffic aggregate can appear in a queue at once (gives queue
   overflow and loss).  If other PDBs are using the same PHB within the
   domain, that must be taken into account.

6.1 Considerations in specifying long-term or average PDB attributes

   To characterize the average or long-term behavior for the foo PDB we
   must explore a number of questions, for instance: Can the DS domain
   handle the average foo traffic flow?  Is that answer topology
   dependent or are there some specific assumptions on routing which
   must hold for the foo PDB to preserve its "adequately provisioned"
   capability?  In other words, if the topology of D changes suddenly,
   will the foo PDB's attributes change?  Will its loss rate
   dramatically increase?

   Let domain D in figure 4 be an ISP ringing the U.S. with links of
   bandwidth B and with N tails to various metropolitan areas.  Inside
   D, if the link between the node connected to A and the node connected
   to Z goes down, all the foo traffic aggregate between the two nodes
   must transit the entire ring: Would the bounded behavior of the foo
   PDB change?  If this outage results in some node of the ring now
   having a larger arrival rate to one of its links than the capacity of
   the link for foo's traffic aggregate, clearly the loss rate would
   change dramatically.  In this case, topological assumptions were made
   about the path of the traffic from A to Z that affected the
   characteristics of the foo PDB.  If these topological assumptions no
   longer hold, the loss rate of packets of the foo traffic aggregate
   transiting the domain could change; for example, a characteristic
   such as "loss rate no greater than 1% over any interval larger than
   10 minutes." A PDB specification should spell out the assumptions
   made on preserving the attributes.

                  ____X________X_________X___________          /
                 /                                   \    L   |
         A<---->X                                     X<----->|  E
                |                                     |       |
                |               D                     |        \
         Z<---->X                                     |
                |                                     |
                         X                 X

        Figure 4: ISP and DS domain D connected in a ring and
                  connected to DS domain E

Nichols & Carpenter          Informational                     [Page 17]

RFC 3086             Diffserv per Domain Behaviors            April 2001

6.2 Considerations in specifying short-term or bursty PDB attributes

   Next, consider the short-time behavior of the traffic aggregate
   associated with a PDB, specifically whether permitting the maximum
   bursts to add in the same manner as the average rates will lead to
   properties that aggregate or under what conditions this will lead to
   properties that aggregate.  In our example, if domain D allows each
   of the uplinks to burst p packets into the foo traffic aggregate, the
   bursts could accumulate as they transit the ring.  Packets headed for
   link L can come from both directions of the ring and back-to-back
   packets from foo's traffic aggregate can arrive at the same time.  If
   the bandwidth of link L is the same as the links of the ring, this
   probably does not present a buffering problem.  If there are two
   input links that can send packets to queue for L, at worst, two
   packets can arrive simultaneously for L.  If the bandwidth of link L
   equals or exceeds twice B, the packets won't accumulate.  Further, if
   p is limited to one, and the bandwidth of L exceeds the rate of
   arrival (over the longer term) of foo packets (required for bounding
   the loss) then the queue of foo packets for link L will empty before
   new packets arrive.  If the bandwidth of L is equal to B, one foo
   packet must queue while the other is transmitted.  This would result
   in N x p back-to- back packets of this traffic aggregate arriving
   over L during the same time scale as the bursts of p were permitted
   on the uplinks.  Thus, configuring the PDB so that link L can handle
   the sum of the rates that ingress to the foo PDB doesn't guarantee
   that L can handle the sum of the N bursts into the foo PDB.

   If the bandwidth of L is less than B, then the link must buffer
   Nxpx(B-L)/B foo packets to avoid loss.  If the PDB is getting less
   than the full bandwidth L, this number is larger.  For probabilistic
   bounds, a smaller buffer might do if the probability of exceeding it
   can be bounded.

   More generally, for router indegree of d, bursts of foo packets might
   arrive on each input.  Then, in the absence of any additional traffic
   conditioning, it is possible that dxpx(# of uplinks) back-to-back foo
   packets can be sent across link L to domain E.  Thus the DS domain E
   must permit these much larger bursts into the foo PDB than domain D
   permits on the N uplinks or else the foo traffic aggregate must be
   made to conform to the TCA for entering E (e.g., by shaping).

   What conditions should be imposed on a PDB and on the associated PHB
   in order to ensure PDBs can be concatenated, as across the interior
   DS domains of figure 1?  Traffic conditioning for constructing a PDB
   that has certain attributes across a DS domain should apply
   independently of the origin of the packets.  With reference to the

Nichols & Carpenter          Informational                     [Page 18]

RFC 3086             Diffserv per Domain Behaviors            April 2001

   example we've been exploring, the TCA for the PDB's traffic aggregate
   entering link L into domain E should not depend on the number of
   uplinks into domain D.

6.3 Remarks

   This section has been provided as motivational food for thought for
   PDB specifiers.  It is by no means an exhaustive catalog of possible
   PDB attributes or what kind of analysis must be done.  We expect this
   to be an interesting and evolutionary part of the work of
   understanding and deploying differentiated services in the Internet.
   There is a potential for much interesting research work.  However, in
   submitting a PDB specification to the Diffserv WG, a PDB must also
   meet the test of being useful and relevant by a deployment
   experience, described in section 8.

7 A Reference Per-Domain Behavior

   The intent of this section is to define as a reference a Best Effort
   PDB, a PDB that has little in the way of rules or expectations.

7.1 Best Effort PDB

7.1.1 Applicability

   A Best Effort (BE) PDB is for sending "normal internet traffic"
   across a diffserv network.  That is, the definition and use of this
   PDB is to preserve, to a reasonable extent, the pre-diffserv delivery
   expectation for packets in a diffserv network that do not require any
   special differentiation.  Although the PDB itself does not include
   bounds on availability, latency, and packet loss, this does not
   preclude Service Providers from engineering their networks so as to
   result in commercially viable bounds on services that utilize the BE
   PDB.  This would be analogous to the Service Level Guarantees that
   are provided in today's single-service Internet.

   In the present single-service commercial Internet, Service Level
   Guarantees for availability, latency, and packet delivery can be
   found on the web sites of ISPs [WCG, PSI, UU].  For example, a
   typical North American round-trip latency bound is 85 milliseconds,
   with each service provider's site information specifying the method
   of measurement of the bounds and the terms associated with these
   bounds contractually.

Nichols & Carpenter          Informational                     [Page 19]

RFC 3086             Diffserv per Domain Behaviors            April 2001

7.1.2 TCS and PHB configurations

   There are no restrictions governing rate and bursts of packets beyond
   the limits imposed by the ingress link.  The network edge ensures
   that packets using the PDB are marked for the Default PHB (as defined
   in [RFC2474]), but no other traffic conditioning is required.
   Interior network nodes apply the Default PHB on these packets.

7.1.3 Attributes of this PDB

   "As much as possible as soon as possible".

   Packets of this PDB will not be completely starved and when resources
   are available (i.e., not required by packets from any other traffic
   aggregate), network elements should be configured to permit packets
   of this PDB to consume them.

   Network operators may bound the delay and loss rate for services
   constructed from this PDB given knowledge about their network, but
   such attributes are not part of the definition.

7.1.4 Parameters


7.1.5 Assumptions

   A properly functioning network, i.e., packets may be delivered from
   any ingress to any egress.

7.1.6 Example uses

   1. For the normal Internet traffic connection of an organization.

   2. For the "non-critical" Internet traffic of an organization.

   3. For standard domestic consumer connections

7.1.7 Environmental Concerns

   There are no environmental concerns specific to this PDB.

7.1.8 Security Considerations for BE PDB

   There are no specific security exposures for this PDB.  See the
   general security considerations in [RFC2474] and [RFC2475].

Nichols & Carpenter          Informational                     [Page 20]

RFC 3086             Diffserv per Domain Behaviors            April 2001

8 Guidelines for writing PDB specifications

   G1. Following the format given in this document, write a draft and
   submit it as an Internet Draft.  The document should have "diffserv"
   as some part of the name.  Either as an appendix to the draft, or in
   a separate document, provide details of deployment experience with
   measured results on a network of non-trivial size carrying realistic
   traffic and/or convincing simulation results (simulation of a range
   of modern traffic patterns and network topologies as applicable).
   The document should be brought to the attention of the diffserv WG
   mailing list, if active.

   G2. Initial discussion should focus primarily on the merits of the
   PDB, though comments and questions on the claimed attributes are
   reasonable.  This is in line with the Differentiated Services goal to
   put relevance before academic interest in the specification of PDBs.
   Academically interesting PDBs are encouraged, but would be more
   appropriate for technical publications and conferences, not for
   submission to the IETF.  (An "academically interesting" PDB might
   become a PDB of interest for deployment over time.)

   The implementation of the following guidelines varies, depending on
   whether there is an active diffserv working group or not.

   Active Diffserv Working Group path:

   G3. Once consensus has been reached on a version of a draft that it
   is a useful PDB and that the characteristics "appear" to be correct
   (i.e., not egregiously wrong) that version of the draft goes to a
   review panel the WG co-chairs set up to audit and report on the
   characteristics.  The review panel will be given a deadline for the
   review.  The exact timing of the deadline will be set on a case-by-
   case basis by the co-chairs to reflect the complexity of the task and
   other constraints (IETF meetings, major holidays) but is expected to
   be in the 4-8 week range.  During that time, the panel may correspond
   with the authors directly (cc'ing the WG co-chairs) to get
   clarifications.  This process should result in a revised draft and/or
   a report to the WG from the panel that either endorses or disputes
   the claimed characteristics.

   G4. If/when endorsed by the panel, that draft goes to WG last call.
   If not endorsed, the author(s) can give an itemized response to the
   panel's report and ask for a WG Last Call.

Nichols & Carpenter          Informational                     [Page 21]

RFC 3086             Diffserv per Domain Behaviors            April 2001

   G5. If/when passes Last Call, goes to ADs for publication as a WG
   Informational RFC in our "PDB series".

   If no active Diffserv Working Group exists:

   G3. Following discussion on relevant mailing lists, the authors
   should revise the Internet Draft and contact the IESG for "Expert
   Review" as defined in section 2 of RFC 2434 [RFC2434].

   G4. Subsequent to the review, the IESG may recommend publication of
   the Draft as an RFC, request revisions, or decline to publish as an
   Informational RFC in the "PDB series".

9 Security Considerations

   The general security considerations of [RFC2474] and [RFC2475] apply
   to all PDBs.  Individual PDB definitions may require additional
   security considerations.

10 Acknowledgements

   The ideas in this document have been heavily influenced by the
   Diffserv WG and, in particular, by discussions with Van Jacobson,
   Dave Clark, Lixia Zhang, Geoff Huston, Scott Bradner, Randy Bush,
   Frank Kastenholz, Aaron Falk, and a host of other people who should
   be acknowledged for their useful input but not be held accountable
   for our mangling of it.  Grenville Armitage coined "per domain
   behavior (PDB)" though some have suggested similar terms prior to
   that.  Dan Grossman, Bob Enger, Jung-Bong Suk, and John Dullaert
   reviewed the document and commented so as to improve its form.


   [RFC2474] Nichols, K., Blake, S. Baker, F. and D. Black, "Definition
             of the Differentiated Services Field (DS Field) in the IPv4
             and IPv6 Headers", RFC 2474, December 1998.

   [RFC2475] Blake, S., Black, D., Carlson, M., Davies, E., Wang, Z. and
             W. Weiss, "An Architecture for Differentiated Services",
             December 1998.

   [RFC2597] Heinanen, J., Baker, F., Weiss, W. and J. Wroclawski,
             "Assured Forwarding PHB Group", RFC 2597, June 1999.

   [RFC2598] Jacobson, V., Nichols, K. and K. Poduri, "An Expedited
             Forwarding PHB", RFC 2598, June 1999.

Nichols & Carpenter          Informational                     [Page 22]

RFC 3086             Diffserv per Domain Behaviors            April 2001

   [RFC2698] Heinanen, J. and R. Geurin, "A Two Rate Three Color
             Marker", RFC 2698, June 1999.

   [MODEL]   Bernet, Y., Blake, S., Grossman, D. and A. Smith, "An
             Informal Management Model for Diffserv Routers", Work in

   [MIB]     Baker, F., Chan, K. and A. Smith, "Management Information
             Base for the Differentiated Services Architecture", Work in

   [VW]      Jacobson, V., Nichols, K. and K. Poduri, "The 'Virtual
             Wire' Per-Domain Behavior", Work in Progress.

   [WCG]     Worldcom, "Internet Service Level Guarantee",

   [PSI]     PSINet, "Service Level Agreements",

   [UU]      UUNET USA Web site, "Service Level Agreements",

   [RFC2434] Alvestrand, H. and T. Narten, "Guidelines for IANA
             Considerations", BCP 26, RFC 2434, October 1998.

Authors' Addresses

   Kathleen Nichols
   Packet Design, LLC
   2465 Latham Street, Third Floor
   Mountain View, CA 94040


   Brian Carpenter
   c/o iCAIR
   Suite 150
   1890 Maple Avenue
   Evanston, IL 60201


Nichols & Carpenter          Informational                     [Page 23]

RFC 3086             Diffserv per Domain Behaviors            April 2001

Full Copyright Statement

   Copyright (C) The Internet Society (2001).  All Rights Reserved.

   This document and translations of it may be copied and furnished to
   others, and derivative works that comment on or otherwise explain it
   or assist in its implementation may be prepared, copied, published
   and distributed, in whole or in part, without restriction of any
   kind, provided that the above copyright notice and this paragraph are
   included on all such copies and derivative works.  However, this
   document itself may not be modified in any way, such as by removing
   the copyright notice or references to the Internet Society or other
   Internet organizations, except as needed for the purpose of
   developing Internet standards in which case the procedures for
   copyrights defined in the Internet Standards process must be
   followed, or as required to translate it into languages other than

   The limited permissions granted above are perpetual and will not be
   revoked by the Internet Society or its successors or assigns.

   This document and the information contained herein is provided on an


   Funding for the RFC Editor function is currently provided by the
   Internet Society.

Nichols & Carpenter          Informational                     [Page 24]